I want to read and write ECU 68H916.
For Kawasaki ZX-12R ECU
Previously
CABLE16/32 BDM
Interface Cable For CPU16 and CPU32
P:617-353-9206
F:617-353-9205
was on sale.
I would like to connect via BDM
Please tell me what system I need to do this.
Flat Cable.interface board.software....etc
Thank you.
Greetings,
The right hardware to buy is the Multilink Universal FX, which is the only hardware we sell that supports the HC16 architecture:
https://www.pemicro.com/products/product_viewDetails.cfm?product_id=15320180
You will also want to buy a license for PROG-HL-16Z to be able to memory dump, read, write, and verify memory contents. Then all you need is the object file you want to program and use that within PROG software:
https://www.pemicro.com/products/product_viewDetails.cfm?product_id=15320181
You do not need to buy any accessories like cables because it will be included with your purchase.
Takao
Thank you for your reply.
Is it correct to say that MCU = 68H916 is the same group as the HC16 series?
When I purchased Multilink Universal FX, it supported MCU = 68H916 and could read and write.
Is this only hardware and no software?
If I purchase a PROG-HL-16Z license together with Multilink Universal FX, will it be compatible with MCU = 68H916?
Is the data read from MCU=68H916 a Hex file?
Once I can read the data from the MCU, I would like to change the data using the Hex editing software I usually use and then write it to the MCU again.
Greetings,
Just buying the multilink comes with no software. You must buy the PROG-HL-16Z if you want to read/write to the HC16 device. Your device is a HC16 device.
The read data will be in srecord format. You can still modify it with a text editor. OR you can attempt to convert it to HEX (using some kind of utility you might be able to find online) and then modify. Our software can take srecord, hex, bin, and elf file to program so you would not need to convert it back to srecord.
Takao
Does it have a checksum function?
If it change the ECU data for tuning, the engine will not start unless you change the checksum at the same time.
example
Read data from ECU (68H916)
Change the data for tuning on the computer
Correctly change the checksum on the data when flashing that data to the ECU
Also, if I purchase Multilink Universal FX, does it come with a manual for pinout data?
Thank you.
Greetings,
You can get the pinout and documents on our website even before purchase:
https://www.pemicro.com/downloads/download_file.cfm?download_id=376
Are the checksum part of an ECC? The checksum should be automatically calculated each time a page of memory is erased or programmed. This is not something users can manipulate on their own.
Takao
Hi.
I want to order.
How to how can I pay?
I want via Paypal.
Order #: 106416
Greetings,
The PO needs to be accepted before you can pay for your order. Please wait for the sales department to make adjustments to your order for shipping costs.
Takao
Yes I know .but how to pay via paypal?
I found via Paypal account.
do I need to pay $36.00 (EFT Bank Processing fee) also?
If I change my payment method from EFT to Paypal, will the shipping cost increase?
Payment method EFT = Shipping fee $10
Payment method Paypal = Shipping fee $39.71
With Paypal, you have to pay 5% fee for International customers, but you do not need to pay EFT.
With EFT, you have to pay the $36 fee.
Shipping costs will be depending on our DHL rate which our sales representative will contact you tomorrow about.
DHL $10 shipping fee will be removed.
Takao