Cart New Account Login

HomeAbout usProductsSupportForumsBlogCustomer Service

search inside this forum
search inside all forums
Mpc5554/mpc555
Ehsan N. Mar 16, 2019 at 11:28 AM (11:28 hours)
Staff: Takao Y.

  • Hi
    I want to read and write mpc5xxx and mpc555 specially reading program from chip is important for me . Which device is good for me ? Can I read program with cyclone Universal Fx?
    Thanks alot.




    Comments

  • Greetings,

    This discussion involves hardware and software.

    The hardware you require to read and write to these devices are either the Multilink Universal FX, the Cyclone Universal, or the Cyclone Universal FX. All other options will not support your devices.

    If you got any of the cyclone hardware, then you do not require any software purchases.

    Cyclone Universal:
    http://www.pemicro.com/products/product_viewDetails.cfm?product_id=15320165
    Cyclone Universal FX:
    http://www.pemicro.com/products/product_viewDetails.cfm?product_id=15320167

    If you got the multilink hardware, you will require two separate software. One software called PROGPPCZ for the MPC555 device, and the PROGPPCNEXUS for the MPC5xxx devices.
    Multilink Universal FX:
    http://www.pemicro.com/products/product_viewDetails.cfm?product_id=15320143
    PROGPPCZ:
    http://www.pemicro.com/products/product_viewDetails.cfm?product_id=121
    PROGPPCNEXUS:
    http://www.pemicro.com/products/product_viewDetails.cfm?product_id=15320089


    Takao Yamada

  • Hi
    I bought syclone universal Fx.
    Please tell how can I read program from mpc5554 and save it?
    Thanks alot.

  • Greetings,

    You need to use the PROGPPCNEXUS software found free on the cyclone software package for cyclone users. Load the algorithm for your device and use the "Upload module" to read and save it in S-record format.


    Takao Yamada

  • Hi
    Today I started working with my device. My first problem was that lcd doesn't work not light dead completely after that l checked device device can connect with pc and l could read mpc5554 with Port C but, l couldn't read mpc555 with Port G and I had error(warning- an Asynchronous Reset Has occurred)
    . I checked all connections, finally I realized that DIDO is connected to GND. What I have to do?
    Please help me.

  • Greetings,

    Your LCD screen should not be dead and you should get it fixed.

    What do you mean DIDO is connected to GND? Is it shorted? or just no activity on DIDO so it looks to be low signal all the time?

    If it is shorted, then do the following test. Disconnect the MPC555 from the cyclone, what is the state of DIDO on your board? and what is the state of DIDO on the cyclone? Which side is shorted?


    Takao Yamada

  • Hi
    How can I fix lcd? It can be software problem or not?
    I disconnected syclone from Target and after that checked both sides, Target is ok and these two pins are not short circuit but in cyclone shorted together.

  • Greetings,

    Sounds like the cyclone is damaged. Where did you buy this cyclone? You should contact the vendor from who you bought it and get a warranty exchange if within their warranty timeframe.


    Takao Yamada

  • Greetings,

    Any update on this?


    Takao Yamada

  • Hi
    I sent it back to seller and I am waiting for it.
    Thanks alot for your attention.
    Thanks again.

Add comment


   Want to comment? Please login or create a new PEmicro account.







© 2019 P&E Microcomputer Systems Inc.
Website Terms of Use and Sales Agreement