Cart New Account Login

HomeAbout usProductsSupportForumsBlogCustomer Service
   Home P&E Customer Support FAQs - Frequently Asked Questions Matching FAQs
Frequently Asked Questions
Find more FAQs
User
Rank
FAQ ID / Question
10.00 ID 66 I am using the PROG08SZ flash programmer, Mon08 Cyclone, or Cyclone Pro to program 68HC908QY, 68HC908QT, 68HC908LB, or 68HC908QL devices and sometimes the devices do not verify. What is the problem?
10.00 ID 90 Your USB ColdFire Multilink uses PST[3:0] signals, but all my processor has is the PST_ALL signal. How do I use the Multilink or Cyclone Max with this configuration?
10.00 ID 227 How do I switch between Lock-Step Mode (LSM) and Dual-Processor Mode (DPM) on a MPC564xL PowerPC Nexus devices?
10.00 ID 224 Can your programming software calculate and return a checksum?
10.00 ID 230 Why do I see the Power Dialog warning when trying to debug or flash program my chip in PROG, ICD, UNIT, or 3rd party software like Codewarrior? How can I prevent this from happening?
10.00 ID 40 I am using an HC12 device in expanded mode, are there some special considerations for this?
9.99 ID 211 My classic Codewarrior or other 3rd party software with PEmicro support will not detect my PEmicro hardware tool or fails to connect to my target. What can I do to fix this?
9.98 ID 121 When using a programming algorithm to program an external flash device, is there a simple way to test the processor's chip select configuration to make sure it's configured properly?
9.98 ID 123 How can I program a pre-calculated trim value into my HCS08/RS08/CFV1 device to be loaded at run time?
9.98 ID 52 I am getting an EPrivilege Exception when running PEmicro software. What is the problem?
9.98 ID 218 How do I partition my FlexNVM on the Kinetis to have Data flash and EEPROM backup flash memory? (e.g. K10DX128, K20DX256, K60FX512)
9.97 ID 42 I am attempting to program external flash connected to my embedded processor. Either the erase, program, or show module does not work. What is the most likely sources of problems?
9.95 ID 83 I recently purchased a USB-ML-12 Rev. B, but it does not work with my debugger/programmer. The USB-ML-12 module is not detected by software. I also have a USB-ML-12 Rev. A, which works fine. What shall I do?
9.94 ID 88 How do I update the Firmware on my Cyclone?
9.89 ID 78 My USB Multilink stopped working. It was working just fine last time I used it, however now the software says the port is "undetected"! The Blue and orange LED are on... help!
9.83 ID 89 I try to install your software, but installation fails with this message:

There are currently 2 open applications using WinDriver. Please close all applications and press Retry. To reload WinDriver, press Cancel and reboot.

How do I solve this?

9.77 ID 29 The connection assistant dialog indicates that my USB Multilink or Cyclone is undetected even though I have connected the hardware to my USB port. What should I do?
9.74 ID 61 When I load the ICD debugger or PROG programmer, Norton Internet Security tells me it is attempting to access the internet, Why?
9.74 ID 63 When I run the command-line programmer which its path has a space in it, or run the programmer with a configuration file whose file name has a space in it, I get an error:

Error - Invalid command line parameter. ERROR 43 during script!

How do I fix this problem?

9.68 ID 74 I would like to preserve some data in my flash or eeprom. However, when I erase the module I lose this data. What can I do?
9.63 ID 206 How do I transfer my existing software to another PC?
9.60 ID 94 I have secured my MCF5213 ColdFire device and can no longer access it. How can I unsecure it?
9.56 ID 1 I was working with my HCS12(X) target processor and suddenly I can no longer communicate with it. Any ideas?
9.50 ID 68 Why are the Cyclones preconfigured with names, and what is the basis for the names?
9.26 ID 4 I am having trouble communicating with a PEmicro parallel port debug interface cable. What should I try?
9.21 ID 3 When I try to program my S-Record, I get an "address out of range" or similar error. My code is definitely within the valid flash ranges of $4000-$FFFF. Why can't I program the flash?
4.00 ID 229 I cannot see PEmicro hardware interfaces under Windows 10 Anniversary addition, how do I update to latest PEmicro drivers?
3.71 ID 190 How do I activate my PEmicro software?
2.64 ID 28 I am interested in launching the CPROGxx command-line flash programmer from my own application, and reading the resultant error code. Is there some simple way to do this from a Windows based application?
1.57 ID 210 Does your software require administrative rights?
1.50 ID 30 I launched the command-line CPROGxx flash programmer, saw a window flicker up, and then disappear. How do I know what happened?
1.32 ID 87 What processors does PKGPPCNEXUS support?
1.31 ID 200 I am unable to install software on my PC which is running Windows 7 and/or 64 bit OS.
1.14 ID 125 Do I need to wire the PST signals to the debug connector on my ColdFire V2/3/4 target if I want to determine if the device is running or halted?
1.03 ID 41 How can I use CPROG to program dynamic data, such as a serial number, into my product where the number changes for each device I am programming?
0.76 ID 50 I am trying to program EEPROM of 9S12A128B microprocessor using CPROG12z and PROG12z software and get error 39: Error converting hexadecimal command. What am I doing wrong?
0.38 ID 49 My interrupts don't seem to be working and I'm using an HC(S)12 with paged FLASH. How can I get them to function properly?
0.30 ID 205 My PROG and ICD are not working on my new computer. How much does it cost to upgrade my software?
0.00 ID 228 I own PEmicro algorithms, software, or plugin. Where and how do I get the latest version?
0.00 ID 222 I am having sporadic failures trying to debug my Kinetis microprocessor with a USB-ML-Universal hardware interface due to some ringing on CLK line. What can be done to address this issue?

© 2017 P&E Microcomputer Systems Inc.
Website Terms of Use and Sales Agreement