Cart New Account Login

HomeAbout usProductsSupportForumsBlogCustomer Service
   Home P&E Customer Support FAQs - Frequently Asked Questions Matching FAQs
Frequently Asked Questions
Find more FAQs
User
Rank
FAQ ID / Question
10.00 ID 90 Your USB ColdFire Multilink uses PST[3:0] signals, but all my processor has is the PST_ALL signal. How do I use the Multilink or Cyclone Max with this configuration?
10.00 ID 230 Why do I see the Power Dialog warning when trying to debug or flash program my chip in PROG, ICD, UNIT, or 3rd party software like Codewarrior? How can I prevent this from happening?
10.00 ID 34 On the ColdFire BDM cable connector, are the PST and DDATA signals used?
10.00 ID 40 I am using an HC12 device in expanded mode, are there some special considerations for this?
9.99 ID 75 I get a Blue Screen crash when Windows attempts to install the drivers for my USB Hardware Interface when I plug it in. What can I do?
9.98 ID 52 I am getting an EPrivilege Exception when running PEmicro software. What is the problem?
9.97 ID 42 I am attempting to program external flash connected to my embedded processor. Either the erase, program, or show module does not work. What is the most likely sources of problems?
9.95 ID 83 I recently purchased a USB-ML-12 Rev. B, but it does not work with my debugger/programmer. The USB-ML-12 module is not detected by software. I also have a USB-ML-12 Rev. A, which works fine. What shall I do?
9.94 ID 196 How do I use OSBDM/OSJTAG interface under Codewarrior 10.1 and higher?
9.89 ID 78 My USB Multilink stopped working. It was working just fine last time I used it, however now the software says the port is "undetected"! The Blue and orange LED are on... help!
9.83 ID 89 I try to install your software, but installation fails with this message:

There are currently 2 open applications using WinDriver. Please close all applications and press Retry. To reload WinDriver, press Cancel and reboot.

How do I solve this?

9.82 ID 119 How do I extend the ribbon cable that connects PEmicro's hardware to my target?
9.77 ID 29 The connection assistant dialog indicates that my USB Multilink or Cyclone is undetected even though I have connected the hardware to my USB port. What should I do?
9.68 ID 74 I would like to preserve some data in my flash or eeprom. However, when I erase the module I lose this data. What can I do?
9.60 ID 94 I have secured my MCF5213 ColdFire device and can no longer access it. How can I unsecure it?
9.50 ID 68 Why are the Cyclones preconfigured with names, and what is the basis for the names?
9.37 ID 203 I'm getting errors installing your latest Drivers on Windows XP 64 bit. I am seeing driver installation errors while installing Codewarrior 10.3 on Windows XP 64 bit.
9.26 ID 4 I am having trouble communicating with a PEmicro parallel port debug interface cable. What should I try?
4.59 ID 33 Are there any guidelines for using PEmicro's BDM Cables?
4.00 ID 229 I cannot see PEmicro hardware interfaces under Windows 10 Anniversary addition, how do I update to latest PEmicro drivers?
3.00 ID 7 How much current does the USB-ML-12 draw from the target?
2.87 ID 77 I wish to add a parallel port to my laptop to work with one of your parallel port debug cables. Is there a recommended one?
2.80 ID 64 For CABLECF and CABLECF_LV, at what voltage should my PC parallel port be operating?
2.54 ID 53 Which ColdFire BDM cable do I need, CABLECF (5 volts) or CABLECF_LV (3.3 volts)?
2.14 ID 59 I am using one of your MON08 interfaces to debug my target and also to supply it a clock across the ribbon cable. Supplying the clock couples noise into the other MON08 signals, how can I decrease this?
2.09 ID 6 How much current does the BDM multilink draw from the target?
1.69 ID 35 What is the J2 connector for on the ICD Cable (CPU16/CPU32)?
1.50 ID 30 I launched the command-line CPROGxx flash programmer, saw a window flicker up, and then disappear. How do I know what happened?
1.05 ID 84 I have a Cyclone Pro / BDM Multilink / USB-ML-12 cable and a MC9S12 target. When I attempt to use PROG12Z application I receive the following error message in the status window:

Speed test (ESC to abort) ... done.
Could not find appropriate io_delay_cnt.

How do I diagnose the problem?

1.03 ID 36 What are the differences between a Rev. D/E Coldfire interface cable and a Rev. F Coldfire interface cable?
0.28 ID 191 I am unable to enumerate my USB-ML-MON08 RevB or USB-ML-12 RevA under the 32 bit versions of Windows Vista/7 or the 64 bit versions of Windows XP/Vista/7.
0.01 ID 193 My CableCF or CableCFLV parallel port ColdFire programmer isn't working. What should I do?
0.00 ID 222 I am having sporadic failures trying to debug my Kinetis microprocessor with a USB-ML-Universal hardware interface due to some ringing on CLK line. What can be done to address this issue?

© 2017 P&E Microcomputer Systems Inc.
Website Terms of Use and Sales Agreement