Cart New Account Login

HomeAbout usProductsSupportForumsBlogCustomer Service
   Home P&E Customer Support FAQs - Frequently Asked Questions Matching FAQs
Frequently Asked Questions
Find more FAQs
User
Rank
FAQ ID / Question
10.00 ID 66 I am using the PROG08SZ flash programmer, Mon08 Cyclone, or Cyclone Pro to program 68HC908QY, 68HC908QT, 68HC908LB, or 68HC908QL devices and sometimes the devices do not verify. What is the problem?
10.00 ID 90 Your USB ColdFire Multilink uses PST[3:0] signals, but all my processor has is the PST_ALL signal. How do I use the Multilink or Cyclone Max with this configuration?
10.00 ID 227 How do I switch between Lock-Step Mode (LSM) and Dual-Processor Mode (DPM) on a MPC564xL PowerPC Nexus devices?
10.00 ID 226 Why am I getting Error $001B when I try to do stand alone programming with my Cyclone?
10.00 ID 217 Why am I getting Error $7009 when I try to do stand alone programming with my Cyclone?
10.00 ID 40 I am using an HC12 device in expanded mode, are there some special considerations for this?
9.99 ID 110 How do I store multiple images onto my Cyclone?
9.98 ID 121 When using a programming algorithm to program an external flash device, is there a simple way to test the processor's chip select configuration to make sure it's configured properly?
9.98 ID 52 I am getting an EPrivilege Exception when running PEmicro software. What is the problem?
9.98 ID 218 How do I partition my FlexNVM on the Kinetis to have Data flash and EEPROM backup flash memory? (e.g. K10DX128, K20DX256, K60FX512)
9.97 ID 42 I am attempting to program external flash connected to my embedded processor. Either the erase, program, or show module does not work. What is the most likely sources of problems?
9.94 ID 88 How do I update the Firmware on my Cyclone?
9.88 ID 199 Do you have any guidelines or troubleshooting tips for programming HCS08/CFV1/RS08 targets with the Cyclone Pro in stand alone mode?
9.82 ID 89 I try to install your software, but installation fails with this message:

There are currently 2 open applications using WinDriver. Please close all applications and press Retry. To reload WinDriver, press Cancel and reboot.

How do I solve this?

9.82 ID 119 How do I extend the ribbon cable that connects PEmicro's hardware to my target?
9.77 ID 67 Once I have configured the Cyclone Max for stand-alone operation, how do I then start the programming sequence from a PC?
9.76 ID 29 The connection assistant dialog indicates that my USB Multilink or Cyclone is undetected even though I have connected the hardware to my USB port. What should I do?
9.74 ID 61 When I load the ICD debugger or PROG programmer, Norton Internet Security tells me it is attempting to access the internet, Why?
9.60 ID 94 I have secured my MCF5213 ColdFire device and can no longer access it. How can I unsecure it?
9.50 ID 68 Why are the Cyclones preconfigured with names, and what is the basis for the names?
9.37 ID 203 I'm getting errors installing your latest Drivers on Windows XP 64 bit. I am seeing driver installation errors while installing Codewarrior 10.3 on Windows XP 64 bit.
9.01 ID 201 I need a list of the error codes for Cyclone stand alone mode.
7.93 ID 202 I am unable to unsecure HCS08QD2 or HCS08QD4 devices with a Cyclone Pro in standalone mode. The Cyclone Pro gives the following error: "Error $00000008" and the Security LED blinks.
5.73 ID 5 Can the Cyclone Pro and Cyclone Max program dynamic data, such as a serial number, in addition to the image which is configured in the unit?
4.00 ID 229 I cannot see PEmicro hardware interfaces under Windows 10 Anniversary addition, how do I update to latest PEmicro drivers?
2.14 ID 59 I am using one of your MON08 interfaces to debug my target and also to supply it a clock across the ribbon cable. Supplying the clock couples noise into the other MON08 signals, how can I decrease this?
1.81 ID 85 I am having trouble programming the EEPROM block on a 908AS32A, 908AZ32A, 908AS60A, or 908AZ60A device? Is there an updated algorithm?
1.25 ID 219 Image Creation Utility fails to create an image from ELF file.
1.03 ID 41 How can I use CPROG to program dynamic data, such as a serial number, into my product where the number changes for each device I am programming?
0.79 ID 106 How can I program both Flash and EEPROM in one step using the Cyclone Pro programmer?
0.00 ID 228 I own PEmicro algorithms, software, or plugin. Where and how do I get the latest version?

© 2017 P&E Microcomputer Systems Inc.
Website Terms of Use and Sales Agreement