Cart New Account Login

HomeAbout usProductsSupportForumsBlogCustomer Service
   Home P&E Customer Support FAQs - Frequently Asked Questions Matching FAQs
Frequently Asked Questions
Find more FAQs
FAQ ID / Question
10.00 ID 90 Your USB ColdFire Multilink uses PST[3:0] signals, but all my processor has is the PST_ALL signal. How do I use the Multilink or Cyclone Max with this configuration?
10.00 ID 227 How do I switch between Lock-Step Mode (LSM) and Dual-Processor Mode (DPM) on a MPC564xL PowerPC Nexus devices?
10.00 ID 230 Why do I see the Power Dialog warning when trying to debug or flash program my chip in PROG, ICD, UNIT, or 3rd party software like Codewarrior? How can I prevent this from happening?
9.98 ID 52 I am getting an EPrivilege Exception when running PEmicro software. What is the problem?
9.97 ID 79 My USB Multilink is not detected by NXP Codewarrior. What should I do?
9.97 ID 42 I am attempting to program external flash connected to my embedded processor. Either the erase, program, or show module does not work. What is the most likely sources of problems?
9.95 ID 83 I recently purchased a USB-ML-12 Rev. B, but it does not work with my debugger/programmer. The USB-ML-12 module is not detected by software. I also have a USB-ML-12 Rev. A, which works fine. What shall I do?
9.83 ID 89 I try to install your software, but installation fails with this message:

There are currently 2 open applications using WinDriver. Please close all applications and press Retry. To reload WinDriver, press Cancel and reboot.

How do I solve this?

9.77 ID 29 The connection assistant dialog indicates that my USB Multilink or Cyclone is undetected even though I have connected the hardware to my USB port. What should I do?
9.63 ID 206 How do I transfer my existing software to another PC?
9.60 ID 94 I have secured my MCF5213 ColdFire device and can no longer access it. How can I unsecure it?
9.50 ID 204 How do I get Virtual Serial port to work using TWR-S12G128 OSBDM board under Codewarrior CW5.1 for S12(X) IDE?
9.26 ID 4 I am having trouble communicating with a PEmicro parallel port debug interface cable. What should I try?
4.00 ID 229 I cannot see PEmicro hardware interfaces under Windows 10 Anniversary addition, how do I update to latest PEmicro drivers?
3.71 ID 190 How do I activate my PEmicro software?
2.14 ID 59 I am using one of your MON08 interfaces to debug my target and also to supply it a clock across the ribbon cable. Supplying the clock couples noise into the other MON08 signals, how can I decrease this?
2.12 ID 80 I am using a C compiler and the PEmicro debugger. What type of debug file format will the PEmicro debugger accept?
1.57 ID 210 Does your software require administrative rights?
1.31 ID 200 I am unable to install software on my PC which is running Windows 7 and/or 64 bit OS.
1.14 ID 125 Do I need to wire the PST signals to the debug connector on my ColdFire V2/3/4 target if I want to determine if the device is running or halted?
0.69 ID 76 Can I debug with optimized code using the PEmicro In-Circuit Debugger and the GNU C compiler? When using the debugger, my variables seem to be displaying the incorrect values.
0.38 ID 49 My interrupts don't seem to be working and I'm using an HC(S)12 with paged FLASH. How can I get them to function properly?
0.38 ID 82 With PKGCFZ_PRO or PKGPPCNEXUS, I created a new project from a template using WinIDE. How do I add my source files to the target application?
0.19 ID 118 How do I configure WinIDE to launch Readelf?
0.08 ID 81 Using PKGCFZ_PRO or PKGPPCNEXUS, where do I configure the GNU compiler settings?
0.03 ID 86 How do I migrate my existing source code to PKGCFZ_PRO or PKGPPCNEXUS?
0.00 ID 216 Why does my debugger (ICDCFZ or ICD32Z) lose communication with the processor when I write to the system registers to initialize memory?
0.00 ID 222 I am having sporadic failures trying to debug my Kinetis microprocessor with a USB-ML-Universal hardware interface due to some ringing on CLK line. What can be done to address this issue?

© 2017 P&E Microcomputer Systems Inc.
Website Terms of Use and Sales Agreement